DELL EMC D-PCM-DY-23 Dell PowerSwitch Campus Deploy 2023 Online Training
DELL EMC D-PCM-DY-23 Online Training
The questions for D-PCM-DY-23 were last updated at Nov 26,2024.
- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 26,2024
How can a network administrator determine which Dell PowerSwitch N-Series switches can be stacked together?
- A . show system stack-type
- B . show supported stack
- C . show stack
- D . show supported switchtype
Based on the topology shown in the graphic, which ports are designated ports?
- A . Switch A, ports Te1/0/1 and Te1/0/2
- B . Switch B, ports Te1/0/3 and Te1/0/4
- C . Switch B port Te1/0/3 and Switch C port Te1/0/6
- D . Switch C, ports Te1/0/5 and Te1/0/6
Refer to the Exhibit.
A network administrator needs to configure the switches to allow traffic to communicate from Host 1 to Host 2.
Which recommended switch port mode should the interconnecting switch ports be configured?
- A . Access
- B . Trunk
- C . VLAN Stacking
- D . Hybrid
Based on the graphic, which command should be used on the Dell EMC N-Series Layer 2 switch to allow both client computers to receive a dynamic IP address?
- A . Console(config)# ip redirects
- B . Console(config)# service dhcp
- C . Console(config)# ip helper-address 192.168.100.250
- D . Console(config)# service-policy in dhcp_250
Refer to the Exhibit.
Switch-1(config)# radius server host 10.1.1.111
Switch-1(config-radius)# key "secretkey"
Switch-1(config-radius)# exit
Switch-1(config)# aaa authentication login "LOCAL-AUTH" local
Switch-1(config)# aaa authentication login "REMOTE-AUTH" radius local
Switch-1(config)# aaa authentication enable "REMOTE-AUTH" radius enable
Switch-1(config)# aaa authentication login default tacacs local
Switch-1(config)# aaa authentication enable default tacacs enable
Switch-1(config)# line telnet Switch-1(config-telnet)# login authentication "REMOTE-AUTH"
Switch-1(config-telnet)# exit Switch-1(config)# line ssh
Switch-1(config-ssh)# login authentication default
Switch-1(config)# exit Switch-1(config)# line console
Switch-1(config-line)# login authentication "LOCAL-AUTH"
Switch-1(config-line)# exit
Which authentication method will be used if a user tries to login to the switch when accessing through SSH?
- A . RADIUS, then fails over to a local user account
- B . Local user account
- C . TACACS, then fails over to a local user account
- D . None
In a Dell EMC Campus networking environment, what are the valid port states for RSTP?
- A . Forwarding, Listening, and Blocking
- B . Forwarding, Learning, and Listening
- C . Forwarding, Learning, and Discarding
- D . Forwarding, Learning, and Blocking
Which command enables Virtual Router Redundancy Protocol in Global Configuration Mode on a Dell OS6 switch?
- A . no vrrp disable
- B . interface vrrp
- C . vrrp enable
- D . ip vrrp
Which OSPF packet type is sent to the neighbor when LSDB difference is detected?
- A . Hello
- B . LSR
- C . LSAck
- D . LSU
Which three statements are true about MLAG? (Select 3)
- A . The peer-link performs the synchronization of FDB and other data.
- B . The backup link is used to prevent split-brain scenarios.
- C . No VLANs can be configured in the peer-link for MLAG switches.
- D . The peer-link can let MLAG switches be in stack for additional redundancy.
- E . User traffic may cross the peer-link for redundancy under some failure scenarios.
A port has been configured with port-security dynamic with one allowable MAC address.
What happens if no frames from that MAC address are seen by the switch within the MAC table age-out time?
- A . Switch will allow the next MAC address it sees to have access on that port
- B . No MAC addresses will be allowed access on that port
- C . Only the original MAC address will ever be allowed on that port
- D . All MAC addresses will be allowed access on that port
Latest D-PCM-DY-23 Dumps Valid Version with 170 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
