DELL EMC D-PCM-DY-23 Dell PowerSwitch Campus Deploy 2023 Online Training
DELL EMC D-PCM-DY-23 Online Training
The questions for D-PCM-DY-23 were last updated at Nov 22,2024.
- Exam Code: D-PCM-DY-23
- Exam Name: Dell PowerSwitch Campus Deploy 2023
- Certification Provider: DELL EMC
- Latest update: Nov 22,2024
A Dell EMC N-Series switch is configured with switchport mode access and ingress filtering.
What is the purpose of ingress filtering?
- A . Allow the port to transmit only untagged frames in the configured VLAN
- B . Allow the port to accept both tagged and untagged frames in the configured VLAN
- C . Allow the port to transmit both tagged and untagged frames in the configured VLAN
- D . Allow the port to accept only untagged frames in the configured VLAN
A network administrator has configured a 4-port port-channel between two Dell EMC Campus networking switches. The physical interfaces show as administratively up and operationally up on both switches. However, the port-channel shows as operationally up on Switch A and operationally down on Switch B.
What is a potential reason for the inconsistent port-channel state?
- A . Switch A is configured to use dynamic port-channels and Switch B is configured to use static port- channels
- B . Ports in the port-channel on Switch A are all the same speed but the ports in the port- channel on Switch B are a mix of speeds
- C . Switch A is configured using channel-group # mode on and Switch B is configured using channel- group # mode auto
- D . N-Series supports a maximum number of physical interfaces that can be included in port-channels on a per-device basis
A customer is reporting that some critical PoE devices are shutting down randomly during daily activities. Devices on ports 1 and 3 should remain powered at all times.
Customer sends the show running-config output:
interface Gi1/0/1
spanning-tree portfast bpdufilter default
switchport access vlan 102
exit
!
interface Gi1/0/2
spanning-tree portfast bpdufilter default
switchport access vlan 102
exit
!
interface Gi1/0/3
spanning-tree portfast bpdufilter default
switchport access vlan 102
exit
!
interface Gi1/0/4
switchport mode trunk
switchport access vlan 205
switchport trunk native vlan 205
switchport trunk allowed vlan 102,106,205
exit
What recommendation should be given?
- A . Change the power profile used by the PoE devices.
- B . Raise the power priority on the ports.
- C . Verify the POE port license has not been exceeded.
- D . Reset the affected ports periodically.
Which configuration tool will allow a network administrator to override routing protocol decisions and determine the forwarding of packets?
- A . SVI
- B . SMTP
- C . RSTP
- D . PBR
In a traditional campus network design using a three-tier hierarchical model, what are the key attributes of the Core layer in this model?
- A . Provides a wide range of services, is highly available, and operates in an active-passive mode
- B . Provides a limited set of services, is highly available, and operates in an always-on mode
- C . Provides a wide range of services, is highly available, and operates in an always-on mode
- D . Provides a limited set of services, is highly available, and operates in an active-passive mode
What describes VRRP advertisements?
- A . Advertisements can be changed independently in the Master router regardless of the backup routers
- B . Advertisements are sent from the Master router once every second by default
- C . Advertisements are fixed values and cannot be changed
- D . Advertisements are sent from the Master router once every three seconds by default
Which command shows IPv6 adjacent devices on Dell OS6?
- A . show ipv6 neighbors
- B . show ipv6 source
- C . show ipv6 nd
- D . show ipv6 brief
Which commands should a network administrator use to configure a RADIUS server on a Dell EMC N-Series switch?
- A . Switch-1(config)# radius 10.1.1.111
Switch-1(config-radius)# name RADIUS-Server
Switch-1(config-radius)# key secretkey - B . Switch-1(config)# radius server auth 10.1.1.111
Switch-l(config-radius)# name
RADIUS-Server
Switch-1(config-radius)# key "secretkey" - C . Switch-1(config)# radius auth 10.1.1.111
Switch-1(config-radius)# name "RADIUS-
Server" Switch-1(config-radius)# key "secretKey" - D . Switch-1(config)# radius auth server 10.1.1.111
Switch-1(config-radius)# name
RADIUS-Server
Switch-1(config-radius)# key "secretKey"
An administrator is attempting to configure MLAG on two pairs of stacked switches; however, the MLAG cannot be created.
What is the most likely reason for this issue?
- A . Stacked switches cannot perform MLAG functions
- B . Stacked switches are in a Daisy Chain topology
- C . Firmware on the MLAG stacks are at different versions
- D . Spanning tree is not enabled on the MLAG stacks
Which bit value is commonly used to indicate video traffic when implementing COS prioritization?
- A . 100
- B . 101
- C . 101101
- D . 101110
Latest D-PCM-DY-23 Dumps Valid Version with 170 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
