Juniper JN0-363 Service Provider Routing and Switching, Specialist (JNCIS-SP) Online Training
Juniper JN0-363 Online Training
The questions for JN0-363 were last updated at Nov 22,2024.
- Exam Code: JN0-363
- Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)
- Certification Provider: Juniper
- Latest update: Nov 22,2024
Which BGP attribute Is used to detect touting loops?
- A . AS path
- B . MED
- C . local preference
- D . next hop
What is the correct order of BGP attributes for active route selection?
- A . next hop -> local preference -> AS path -> MED -> origin
- B . next hop -> AS path -> local preference -> origin -> MED
- C . next hop -> local preference -> AS path -> origin -> MED
- D . next hop -> origin -> local preference -> AS path -> MED
Which new field is added to an IPv6 header as compared lo IPv4?
- A . version
- B . checksum
- C . fragment offset
- D . flow label
How does a Junos device learn about MAC addresses when II is first connected to an Ethernet LAN?
- A . The device sends out a network broadcast message asking tor all devices and MAC
addresses on the network and stores this information In addition lo the interface from which the response was received. - B . The device learns the destination MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.
- C . The device learns the source MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.
- D . The device sends out a network multicast message asking for all devices and MAC addresses on the network and stores this Information in addition to the interface from which the response was received.
Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?
- A . Type 5
- B . Type 7
- C . Type 3
- D . Type 1
Exhibit
You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.
Referring to the exhibit, what is the problem?
- A . The command is only available if non-stop routing is enabled.
- B . The command is only available on the backup Routing Engine.
- C . The command is only available If a backup router is configured.
- D . The command is only available If graceful restart is enabled.
Which statement is correct about IS-IS?
- A . IS-IS is a distance vector routing protocol.
- B . IS-IS is a path vector routing protocol.
- C . IS-IS is a link-state routing protocol.
- D . IS-IS is a classful routing protocol.
Exhibit
Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?
- A . 192.168.1.3
- B . 172.18.1.0/24
- C . 192.108.1.4
- D . 172.26.4.0730
Interface ge-0/0/0.0 connecls yout network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP.
In this scenario, how is this task accomplished?
- A . Remove interface ge-0/0/0.0 from OSPF.
- B . Create a generated route for Interface ge-0/0/0.0.
- C . Add ge-0/0/0.0 as a passive interface In OSPF.
- D . Configure a static route for Interface ge-0/0/0.0.
Interface ge-0/0/0.0 connecls yout network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP.
In this scenario, how is this task accomplished?
- A . Remove interface ge-0/0/0.0 from OSPF.
- B . Create a generated route for Interface ge-0/0/0.0.
- C . Add ge-0/0/0.0 as a passive interface In OSPF.
- D . Configure a static route for Interface ge-0/0/0.0.
Latest JN0-363 Dumps Valid Version with 65 Q&As
Latest And Valid Q&A | Instant Download | Once Fail, Full Refund
